Skip to content

Tally Ho Police Frequencies

We do not have frequencies listed specifically for Tally Ho in Granville County, North Carolina yet. Countywide channels for Granville County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Berea (North Carolina VIPER), about 6 miles away.

About Tally Ho Police Frequencies

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry law-enforcement traffic here: North Carolina VIPER: 10 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Tally Ho, start with the Berea site of North Carolina VIPER, about 6 miles away. Its control channels: 853.1375, 853.75 MHz.

Granville County channels that also cover Tally Ho

Dispatch

AgencyDescriptionFrequency (MHz)ToneModeFCC
Granville County SheriffSheriff 1155.0700
In 156.1500
146.2 PLFMNKIB877

Tactical

AgencyDescriptionFrequency (MHz)ToneModeFCC
Granville County SheriffSheriff 2155.6250
In 158.9700
146.2 PLFMNWNQJ334

North Carolina VIPER

AgencyDescriptionTalkgroupHexMode
Granville County SheriffGranville County Sheriff – Dispatch200024e22D
Granville County SheriffGranville Co Small Town Police200284e3cD
Granville County SheriffGranville Sheriff Investigations200034e23D
Granville County SheriffGranville Sheriff Narc200044e24D
Granville County SheriffGranville Sheriff Patrol200054e25D
Granville County SheriffGranville Co Law Enforcement Operations200124e2cD
Granville County SheriffButner Public Safety Dispatch51527c947D
Granville County SheriffGranville Co Sheriff Administration200004e20D
Granville County SheriffGranville Co Sheriff Civil200014e21D
Granville County SheriffGranville Co Law Enforcement Administration200114e2bD

Nearest trunked radio sites

Distances are measured from the center of Tally Ho.

Berea · North Carolina VIPER
RFSS 1 · Site 5 (hex 5) · NAC 1F0 · about 6 mi away
Control 853.1375, 853.75
Voice 851.2125, 851.6375, 852.25, 852.475, 852.75
Butner · North Carolina VIPER
RFSS 1 · Site 8 (hex 8) · NAC 1F2 · about 7 mi away
Control 853.6125, 853.8125
Voice 851.925, 852.225, 852.3125, 852.725, 853.35
Oxford WT · North Carolina VIPER
RFSS 1 · Site 39 (hex 27) · about 9 mi away
Control 852.975, 853.95
Voice 851.3, 851.7375, 852.3, 852.6, 853.1625
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency do the police use in Tally Ho?

We do not have a dispatch channel listed specifically for Tally Ho. County-level dispatch channels in the same county: Granville County Sheriff 155.0700 MHz (146.2 PL).