Skip to content

Fort Thompson Police Frequencies

We do not have frequencies listed specifically for Fort Thompson in Buffalo County, South Dakota yet. Countywide channels for Buffalo County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Reliance (Medicine Butte) (South Dakota State Radio System), about 11 miles away.

About Fort Thompson Police Frequencies

Quick answer: County-level dispatch that covers Fort Thompson: Buffalo County Sheriff 158.7750 MHz, FM, 141.3 PL. Trunked: South Dakota State Radio System, for example Buffalo County Sheriff talkgroup 1226 (hex 4ca).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry law-enforcement traffic here: South Dakota State Radio System: 7 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Fort Thompson, start with the Reliance (Medicine Butte) site of South Dakota State Radio System, about 11 miles away. Its control channels: 155.655, 156.03 MHz.

Data updated .

Buffalo County channels that also cover Fort Thompson

Dispatch

Dispatch frequencies for Buffalo County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Buffalo County SheriffCounty Sheriff158.7750
In 153.8750
141.3 PLFMWPGW665

South Dakota State Radio System

South Dakota State Radio System talkgroups
AgencyDescriptionTalkgroupHexMode
Buffalo County SheriffLaw 112264caD
Buffalo County SheriffCrow Creek Law 1 Dispatch (14-7)17036a7D
Buffalo County SheriffCrow Creek Agency12078D
Buffalo County SheriffCrow Creek Law1247cD
Buffalo County SheriffSheriff 112254c9D
Buffalo County SheriffLaw 212274cbD
Buffalo County SheriffCrow Creek Law17056a9D

Nearest trunked radio sites

Distances are measured from the center of Fort Thompson.

Reliance (Medicine Butte) · South Dakota State Radio System
RFSS 1 · Site 58 (hex 3A) · NAC 470 · about 11 mi away
Control 155.655, 156.03
Voice 155.85, 159.165
Miller · South Dakota State Radio System
RFSS 1 · Site 10 (hex A) · NAC 47A · about 25 mi away
Control 155.58, 159.27
Voice 159.03, 159.465, 160.065
Iona · South Dakota State Radio System
RFSS 1 · Site 2 (hex 2) · NAC 470 · about 38 mi away
Control 156.015, 159.06, 159.285
Voice 159.69
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency do the police use in Fort Thompson?

We do not have a dispatch channel listed specifically for Fort Thompson. The county sheriff's dispatch channels in the same county: Buffalo County Sheriff 158.7750 MHz, FM, 141.3 PL.

Do the police use a trunked radio system in Fort Thompson?

Yes. The county-level systems that cover Fort Thompson are Law-enforcement talkgroups are listed for South Dakota State Radio System: 7 talkgroups. A trunking scanner is required.

What scanner do I need to listen to police in Fort Thompson?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Fort Thompson?

For Fort Thompson, start with the Reliance (Medicine Butte) site of South Dakota State Radio System. Its control channels are 155.655, 156.03 MHz. Program a control channel first; the scanner finds the voice channels from it.