The short version
Many police channels send a quiet code along with the voice. It is not a password and it does not scramble anything. It tells a receiver "this transmission is for you", so radios do not open for strangers on the same frequency.
| You see | Name | What it is |
|---|---|---|
156.7 PL | CTCSS / PL | A continuous sub-audible tone, in hertz |
074 DPL | DCS / DPL | A sub-audible digital code, three digits |
NAC 293 | NAC | A three-character code on P25 digital channels |
RAN 1 | RAN | A number from 0 to 63 on NXDN digital channels |
CC 5 | Color code | A number from 0 to 15 on DMR digital channels |
| none, or CSQ | Carrier squelch | No code: the receiver opens whenever there is a signal |
PL (CTCSS)
PL means Private Line, Motorola's name for CTCSS, the Continuous Tone-Coded Squelch System. The radio sends a low tone, usually between 67 and 254 hertz, under the voice. You can't hear it because it is below the audible range.
On a listing it is shown as a number, for example 156.7 PL. That is a 156.7 Hz tone.
DPL (DCS)
DPL means Digital Private Line, Motorola's name for DCS, Digital-Coded Squelch. It does the same job as PL, but the code is a digital pattern, written as a three-digit number such as 074 DPL.
Some scanners and programming software show a DPL code with a letter, such as D074N. The N means normal and an I means inverted. Use the number from the listing, and try the inverted form only if the normal one doesn't open.
NAC, RAN and color code
Digital systems have their own version of the same idea:
- NAC (Network Access Code) is for Project 25. It is three hex characters, for example 293. See what NAC and RFSS mean.
- RAN (Radio Access Number) is for NXDN.
- Color code is for DMR.
Like PL and DPL, they filter. They do not encrypt.
CSQ
CSQ is carrier squelch. The receiver opens whenever it hears a signal on the frequency and ignores tones altogether. If a listing has no tone, or shows CSQ, there is nothing to enter.
What to enter in your scanner
- To hear everything on the frequency, set the tone to off (often labelled "Search" or "None"). This is the usual choice. You hear everyone who transmits there.
- To hear only the agency you want, enter the tone from the listing. Your scanner opens only for that tone, which is useful when another system is on the same frequency or when a distant transmitter interferes.
- Use the output tone. The listing shows the tone the repeater sends, which is what your scanner should look for.
- On trunked systems you don't set a tone. The system's control channel does the filtering. For P25, the NAC can usually stay on automatic.
Output frequency and input frequency
A repeater listens on one frequency and re-transmits on another. The listing's main frequency is the output, which is what you tune your scanner to. The "In" frequency is the input, where handheld and car radios transmit to the repeater. A scanner normally listens to the output, because that's where the repeater re-broadcasts both sides of a conversation. The input is shown for completeness.
If a tone doesn't work
- Try the scanner with the tone off. If you hear the channel, the tone was the problem.
- Check whether your scanner is set to PL or DPL, since the two use different settings.
- If the listing shows a DPL code, try the inverted form.
- Remember that tones change. See why a frequency stopped working.
Frequently asked questions
Is a PL tone the same as encryption?
No. A tone filters. Anyone with a scanner set to ignore the tone can hear the channel.
Do I need to enter the tone?
Usually not. Turning the tone off hears the most. Enter it only to cut interference.
What if the listing shows no tone?
Then the channel probably uses carrier squelch. Leave the tone off.
What is the difference between PL and DPL?
Both are sub-audible codes. PL is an analog tone. DPL is a digital code. A scanner has a separate setting for each.